1Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06MODEL: SL-350TRSI-AUE AUSTRALIAN GAS ASSOCIATION APPROVEDApproval Number 5666THIS MANU
10Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 8. SL D-Series Balanced Flue Component Specifications (102mm inner pipe / 16
11Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06VERTICAL FLUEINGVFT. (M)36' MAXIMUM (10.97M)Figure 10.USE SL D-SERIESCOMPONENTS
12Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 12. V H FT. (M) FT. (M)1' MIN.(0.30M) 2
13Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 14. V H FT. (M) FT. (M)1' MIN.(0.30M) 2&apos
14Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 15.USE DVP-SERIESCOMPONENTS ONLY.FLUEING WITH TWO (2) 90° ELBOWSV H H + H11´ M
15Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06FLUEING WITH THREE (3) 90° ELBOWS V H H + H1 FT. (M)
16Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 17.FLUEING WITH THREE (3) 90° ELBOWS1´ MIN. (0.30M) 1´ MAX. (0.30M) 3´ MAX. (0
17Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 18.WARNING: FAILURE TO REMOVEINSULATION IN THE SET OF COL-LARS YOU ARE USING C
18Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06!WARNING: ENSURE THAT THE HEATERGASKET SUPPLIED WITH THE HEATERSEALS BETWEEN THE FIRS
19Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/062. Continue Adding Flue ComponentsTo continue adding flue components in accordance w
2Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06IMPORTANT: Read all instructions carefully before starting installation.Failure to fol
20Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06For Vertical RunsThe flue system must be supported every eight (8) feet(2.4 M) above
21Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06! Figure 27. Ceiling Firestop (Ceiling Side)If the area above the ceiling IS an
22Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06For Vertical Terminations - To locate the flue andinstall the flue sections:• Locate
23Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/061.4 IGNITION SYSTEM WIRING• This gas heater is equipped with an electronic igni-tion
24Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 32.NOTE: IF ANY OF THE ORIGINALWIRE AS SUPPLIED WITH THEAPPLIANCE MUST BE RE-P
25Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 34.1.6 FINISHINGThe minimum clearance to combustibles are 0 fromthe sides, fl
26Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 35.Figure 36.MAKE SURE THE FLAMESARE STEADY—NOTLIFTING OR FLOATING.Installing
27Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/061234561.8 LOG PLACEMENT INSTRUCTIONSLog Set Assembly: LOGS-350CE-DCarefully remove t
28Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06LOG #3 (SRV705-703): Rest log #3 against the right front grate corner and place its s
29Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06LOG #6 (SRV540-704): Place log #6 against the second and third grate bars. If sooting
3Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06TABLE OF CONTENTS1.0 Installation Instructions...
30Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06!!OPERATING CAUTIONS• This appliance may exhibit a slight carbon deposition.• Do not
31Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/062.1 SAFETY & LIGHTING INFORMATIONFollow SAFETY INFORMATION and LIGHTING IN-STRU
32Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06!2.2 FAN OPERATIONThe accessory fan is wired in series with a speed con-trol switch a
33Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06PILOT BRACKETRETAINING SCREWS3.1 REMOVAL OF COVERS FOR SERVICINGA. Contr
34Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/063.5 TROUBLESHOOTING SL-350TRSI-AUEWith proper installation and maintenance,
35Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06(NG, LP) Exploded Parts DiagramService PartsSL-350TRSI-AUEBeginning Manufacturing Da
36Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06SL-350TRSI-AUE Service Parts ListIMPORTANT: When ordering, supply serial and model n
37Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06LIMITED 10 YEAR WARRANTYHEAT & GLO, a brand of Hearth & Home Technologies Inc
38Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06For Service or Replacement Parts Contact:MelbourneJetmaster444 Swan StreetRichmond 31
4Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 1. Diagram of SL-350TRSI-AUE22-3/4 in.(577mm)11-3/8 in.(289mm)16-3/8 in.(414mm
5Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 2. Fireplace Dimensions, Locations, andSpace Requirements1.0 INSTALLATION INSTR
6Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06Figure 4. Framing DimensionsFraming should be constructedof 2 X 4 lumber or heavier
7Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06NOTES: 1. All distances are measured vertically or horizontally along the wall to a po
8Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06TABLE 11.2 FLUE SYSTEM APPROVALSThese models have flue starting collars on both the t
9Heat & Glo • SL-350TRSI-AUE • 2089-902 Rev. B • 6/06NOTE: PIPES OVERLAP 32mm AT EACH JOINT.DVP90ST319mm286mm184mm32mm TYP13mm TYP217mmDVP
Comments to this Manuals